Wood Care

Tung Oil vs Danish Oil vs Teak Oil: What's the Difference?

One pure oil, two blends and the one place none of them belong

November 09, 2026 6 min read
Close view of the Tulipa sculptural solid wood dining table in a natural tone showing curved arches and grain under a bowl of fruit
Quick Answer

Pure tung oil is a single natural oil that soaks in, dries slowly and builds a water-resistant matte to satin finish over many thin coats. Danish oil is a blend of oil, varnish and thinner that is quicker and easier. Teak oil is a similar blend, not oil from teak. None should go over polyurethane.

1 pure oilTung; the others are blends
0 teakIn most teak oil
FlatDry oily rags flat, never balled

Walk down the finishing aisle and three cans look almost the same: tung oil, Danish oil and teak oil. They all promise a warm, natural look. But only one of them is a single oil, and the names say very little about what is inside.

Here is what each one really is, how they compare and when to use them, plus the one situation where you should use none of them.

Tung oil vs Danish oil vs teak oil at a glance

Tung oil (pure) Danish oil Teak oil
What it is Oil pressed from tung tree nuts Blend of oil, varnish and thinner Blend of oil, varnish and thinner, often thinner still
Made from teak? No No Usually not; named for the wood it is sold for
Drying Slow; often a day or more between coats Faster; follow the label Faster; follow the label
Coats Many thin coats Two or three is common Two or three is common
Look Matte to soft satin Satin Satin; some add UV blockers for outdoor use
Best for Patient owners who want a pure oil Indoor furniture, easy first finish Dense, oily woods and many outdoor pieces

"Tung oil finish" on a label does not always mean pure tung oil; some are blends. Read the ingredients or the safety data sheet if it matters to you.

Tulipa sculptural solid wood round dining table in a natural tone with a curved arched base and chairs on a round jute rug
Natural Tone

Pale wood, warm finish

Our Tulipa dining table stands on curved arches of solid wood, 39 to 63 inches across, from $4,290. Like every Woodfurnist piece, it is finished with polyurethane, not oil.

Tung oil: pure, slow and natural

Tung oil is a drying oil: it hardens as it reacts with air. Each thin coat soaks in, then you wipe off the excess. It takes patience, because coats need time to dry and the finish keeps hardening for weeks. The reward is a finish that looks like bare wood, only richer.

Danish oil: the easy middle

Danish oil has no single recipe. Most mix a drying oil with a little varnish and a thinner, so it soaks in like oil but dries faster and leaves slightly more protection. It is forgiving for a first project.

Close view of the Cavora sculptural solid wood coffee table in a walnut tone showing carved arch tunnels and grain with books on top
Grain Up Close

Carved curves in walnut tone

Our Cavora coffee table is carved with arched tunnels through the base, 41 to 63 inches wide, from $2,390. The grain runs around every curve.

Teak oil: a name, not an ingredient

Teak oil was named for the wood it was sold to treat. Most versions are oil and varnish blends similar to Danish oil, often thinned more so they soak into dense, oily woods. Outdoor versions may add UV blockers.

Which one should you use?

Bare indoor wood, first try

  • Danish oil.
  • Two or three coats.
  • Wipe off all excess.

You want a pure oil

  • Pure tung oil.
  • Many thin coats.
  • Plan for slow drying.

Outdoor or oily wood

  • Teak oil made for outdoor use.
  • Re-coat each season.
  • Check for UV protection.
Close view of the Capsula sculptural solid wood coffee table in a natural oak tone showing its smooth rounded loop end and drawer front
Already Finished

A sealed top needs only a soft cloth

Our Capsula coffee table loops into rounded ends with a drawer, 24 to 47 inches wide, from $2,060. Its polyurethane finish needs a dry or barely damp cloth, not oil.

When not to use any of them

  • Over polyurethane, varnish or lacquer: oil cannot soak through and leaves a sticky film. All Woodfurnist pieces are finished with PU, so skip oil entirely.
  • Over old wax: clean the wax off first or the oil will not bond.
  • On a cutting board: choose a product sold for food contact and follow its label.

For cutting boards specifically, follow how to clean and oil a wood cutting board.

Safety Note

Rags soaked in drying oils such as tung, linseed and Danish oil can heat up as they dry and catch fire on their own. Lay used rags flat outdoors to dry, or keep them in a sealed metal can filled with water, then dispose of them as your local rules require.

Close view of the twisted pedestal of the Helixa sculptural solid wood dining table showing spiraling walnut-tone grain on a jute rug
Twisted Grain

A pedestal that spirals

Our Helixa dining table twists its pedestal like a turning trunk, 39 to 59 inches across, from $4,090.

Still deciding between oil and a film finish? Our best finish for a wood table guide compares oil, wax and polyurethane.

Key Takeaway

Pure tung oil is one natural oil that dries slowly over many coats. Danish oil and teak oil are blends of oil, varnish and thinner that dry faster; teak oil is not made from teak. Use them on bare or oiled wood only, never over polyurethane, and always dry oily rags flat or store them in water.

Woodfurnist Design Tip

Test any oil on the underside of a shelf or a scrap of the same wood first. Oil darkens wood, and you cannot take that back.

Keep Exploring

Browse our coffee tables, compare smooth vs natural rough finishes, or read teak vs acacia vs suar.

Frequently Asked Questions

What is the difference between tung oil and Danish oil?

Pure tung oil is a single natural oil that dries slowly. Danish oil is a blend of oil, varnish and thinner that dries faster and is easier to apply.

Is teak oil made from teak?

Usually not. Teak oil is a blend named for the wood it was sold to treat.

Which oil is most water resistant?

Among the three, a fully cured pure tung oil or a varnish-rich Danish oil resists water better than raw oil, but none protects like polyurethane.

Can I put tung oil over polyurethane?

No. It cannot soak through the film and will stay sticky.

Do I need to oil Woodfurnist furniture?

No. Every piece is finished with polyurethane; dust or wipe with a soft cloth instead.

Why are oily rags dangerous?

Drying oils give off heat as they cure, and a bunched rag can trap enough to catch fire. Dry rags flat outdoors or store them in water in a sealed metal can.

Editor's note: Product formulas vary by brand; always follow the label and safety data sheet for drying times, coats and disposal. Woodfurnist finish details come from the finish table on our product pages. Product sizes and prices were checked on woodfurnist.com on November 9, 2026. Room images are styled product images for inspiration. Every piece is made to order in 7 to 10 business days, plus 5 to 7 business days for free US delivery; see our shipping policy.