Wood Care

How to Clean and Oil a Wood Cutting Board

Two minutes after each use, a few minutes each month

November 11, 2026 5 min read
Mapledale live edge solid wood cutting board with a handle holding cheese and cherries beside crackers on a pale countertop
Quick Answer

Wash a wood cutting board by hand with warm soapy water, rinse, towel it off and let it dry standing upright. Never soak it or put it in the dishwasher. Oil it with food-grade mineral oil or a board butter whenever it looks pale or dry, about once a month, and more often when it is new.

0Dishwasher cycles, ever
~MonthlyOil, or when it looks dry
UprightHow to dry it

A wood cutting board asks for two minutes after each use and a few minutes once a month. Do that, and it will stay smooth, flat and clean for years. Skip it, and even a fine board will crack, warp or turn gray.

Daily cleaning in four steps

  1. Scrape off food with a bench scraper or the back of a knife.
  2. Wash both sides with warm water, a little dish soap and a sponge or brush.
  3. Rinse and towel dry right away.
  4. Stand it upright or on a rack so air reaches both sides.
Never Do This

Do not put a wood board in the dishwasher, soak it in the sink or leave it lying flat on a wet counter. Heat and standing water make wood swell unevenly, which leads to warping and cracks.

Mapledale live edge solid wood cutting board with a handle holding blackberries, raspberries and crackers with cheese on the side
Easy Care

A handle for drying upright

Our Mapledale cutting board comes with or without a handle, 16 to 40 inches wide, from $318.99. The handle version can hang to dry. It arrives finished with a food-safe natural oil.

Sanitizing after raw meat

After cutting raw meat, poultry or fish, wash the board with hot soapy water first. For extra sanitizing, the USDA suggests a solution of 1 tablespoon of unscented liquid chlorine bleach per gallon of water: flood the surface, let it stand a few minutes, rinse and dry. Many cooks keep a separate board just for raw meat.

Removing stains and smells

Problem Fix
Garlic or onion smell Sprinkle coarse salt, scrub with half a lemon, rinse and dry
Light stains Baking soda paste, gentle scrub along the grain, rinse
Fuzzy, raised grain Light sanding with fine sandpaper once dry, then oil
Deep knife grooves Sand smooth, or retire the board if grooves stay deep
Small crack along the end Oil well and keep it dry; replace the board if it widens

How to oil a cutting board

  1. Start clean and fully dry, ideally overnight after washing.
  2. Pour on food-grade mineral oil and spread it with a soft cloth over every face and edge.
  3. Let it soak in for several hours or overnight.
  4. Wipe off the excess so the surface is not sticky.
  5. Optional: finish with board butter, a blend of mineral oil and beeswax, for a little more water resistance.

Oil a new board several times in its first weeks, then about once a month, or whenever water stops beading and the wood looks pale.

Mapledale live edge solid wood cutting board with a handle showing wide flowing grain under cheese, tomatoes and blackberries
Oiled Grain

Color that comes back with oil

A freshly oiled board looks deeper and richer, like the Mapledale here. Oil the live edge and the underside too, not only the top.

Which oil to use

Oil Use it? Why
Food-grade mineral oil Yes Food safe, odorless, does not go rancid
Board butter (mineral oil + beeswax) Yes Adds a light water-resistant layer
Olive, vegetable or sunflower oil No Can turn rancid and smell over time
Furniture polish or wax sprays No Not made for food contact
Finishes sold as varnish or polyurethane No Film finishes chip under knives

For how oils differ, see tung oil vs Danish oil vs teak oil; for cutting boards, stick to products sold as food safe.

Key Takeaway

Hand wash with warm soapy water, towel dry and stand the board upright; never soak it or use the dishwasher. Sanitize after raw meat, freshen smells with salt and lemon, and oil with food-grade mineral oil or board butter about once a month. Avoid cooking oils, which can go rancid.

Woodfurnist Design Tip

Oil your board on the same day each month, the night you change the kitchen towels. A habit tied to something you already do is one you will keep.

Keep Exploring

Browse our wooden cutting boards, read the best wood for a cutting board, or compare end grain vs edge grain.

Frequently Asked Questions

How do you clean a wood cutting board?

Scrape, wash with warm soapy water, rinse, towel dry and let it dry standing upright.

Can a wood cutting board go in the dishwasher?

No. Heat and water can warp and crack it.

How do you sanitize a wood cutting board after raw meat?

Wash with hot soapy water, then if you like use the USDA solution of 1 tablespoon unscented liquid bleach per gallon of water, rinse and dry.

How often should you oil a cutting board?

About once a month, or whenever it looks dry. Oil a new board several times in its first weeks.

What oil is best for a cutting board?

Food-grade mineral oil, or a board butter made from mineral oil and beeswax.

Can I use olive oil on a cutting board?

It is better not to. Cooking oils can turn rancid and leave an odor.

Editor's note: Sanitizing guidance follows USDA Food Safety and Inspection Service advice; other care steps are general kitchen practice. Product sizes and prices were checked on woodfurnist.com on November 11, 2026. Every piece is made to order in 7 to 10 business days, plus 5 to 7 business days for free US delivery; see our shipping policy.

More from Woodfurnist